Armstrong Products

Armstrong New Beginning® Extra-Strength Floor Stripper & Cleaner
Armstrong Floor Stripper & Cleaner removes tough ground-in dirt and dissolves wax and polish build-up without damaging your no-wax floors, for all no-wax floors. Test a small hidden area first.

• Floor Preparation: Sweep or vacuum thoroughly
• Application: Use a sponge mop and apply liberally over  3' by 3' area and let stand for several minutes
• Scrub: While still wet and with rubber gloves, scrub the area with a nylon pad or scrub brush. Avoid contact with knees
• Rinse: Take up the liquid with a sponge mop or cloth. Rinse thoroughly with clean, warm water
• Polish: Apply Armstrong Floor Polish

Armstrong ShineKeeper® Floor Polish
For no-wax and linoleum floors that have lost their original shine. Shinekeeper will keep on shining even after repeated washings.

• Floor Preparation: Sweep or vacuum floor thoroughly. Wash and let dry.
• Application: Apply a thin coat with a clean damp sponge mop or wax applicator. Make certain the entire surface is coated. Dries in 30 minutes - no buffing necessary.
• On-going maintenance: Reapply polish as needed - 1 or 2 coats at a time

Armstrong Once 'N Done® No-Rinse Cleaner
No rinse cleaner for vinyl and ceramic flooring. Never leaves a dulling, sticky film, will not hurt tile grout, keeps Armstrong floors looking their best.

• Do not use on solid wood, cork or linoleum floors.
• Routine cleaning: Use 1/2 cap to 1 gallon warm water, wash floor with sponge mop,  no rinsing required
• Extra strength cleaning: Use 3 caps to 1 gallon warm water, wash floor with sponge mop,  no rinsing required
• Tough spots: Use full strength except over ceramic tile, let soak 2-3 minutes, loosen dirt with nylon pad or scrub brush, wipe with clean, damp cloth or sponge

BonaKemi Products

Handle not shown	BonaKemi (BONA?X) Hard Surface Floor Care System (White Terry Cloth Pad) Quick and easy to use. Ideal for light and heavy cleaning. Kit includes: 32 oz. spray bottle of Bona Hard Surface Floor Cleaner 1 washable terry cloth BONA mop head cover 8" x 15" mop head Guide to Caring for Hard Surface Floors Replacement pads available (see below)
BonaKemi (BONA X) Replacement Terry Cloth Mop Head Covers (White Terry Cloth Pad) Fits 8" x 15" mop head Two replacement terry cloth mop head covers Washable and reusable Only fits Bonakemi Hard Surface Floor Care System (see above)

BonaKemi (BONA X) Swedish Formula MicroPlus? Hard Surface Floor Care System - Complete system includes mop, microfiber pad, pole and cleaner. Can be used either dry or wet. The electrostatic action attracts and traps dirt and allergens when used dry. The pad will absorb spills and remove tough stains.

Hard Surface kit includes:

• Specially designed Bona MicroPlus? Mop with 3 piece handle
  
• 4" x 15" mop head
• 32 oz. Spray bottle of Bona Swedish Formula Hard Surface Cleaner
  
• Washable Bona MicroPlus Cleaning Pad with Dust Absorbing Microfibers
  
• Guide to Caring for Hard Surface Floors
  

Directions for use:

• Vacuum, sweep or dry mop to remove any loose dirt or grit. If using the Bona MicroPlus Mop to dry mop, rinse the mop with water before continuing.
  
• Spray - lightly mist a 4x6 area of your floor, or directly mist the Bona MicroPlus Cleaning Pad with cleaner.
  
• Clean - Using a back and forth motion clean the floor surface using your Bona MicroPlus Mop. Finish one area before moving on to the next.
  
• The MicroPlus Cleaning Pads are reusable and washable.
• Do not use fabric softeners, dryer sheets or bleach when washing your MicroPlus Cleaning Pad
  

Replacement pads available (see below)

BonaKemi (BONA?X) MicroPlus? Microfiber Cleaning Replacement Pad (Blue Pad)

• Replacement pad for Bonakemi Swedish Formula MicroPlus? Hard Surface Floor Care System (shown above)
• Only fits 4" x 15" Bona? MicroPlus? Mop Head
  
  
  

BonaKemi (BONA X) MicroPlus Microfiber Dusting Pad (White Pad)

Swedish Formula? MicroPlus? Dusting Pad for the new MicroPlus? Mop. Designed for dry dusting on both hardwood and hard surface floors.

• Its "Super Electrostatic Action" attracts and lifts dust, pet hair, microparticles and common household allergens from your floors' surface.
• The combination of special microfibers engineered into this pad creates the unique static charge which causes dust and debris to be attracted to the pad's fibers.
• And since the pad is reusable and washable up to 300 times, it is more economical than disposable dry dusting pads.
• Only fits 4" x 15" Bona? MicroPlus? Mop Head

Mannington Products

Mannington Heavy Duty Cleaner & Stripper
Dissolves stubborn dirt, built-up floor polish and heel marks. Suitable for all sheet vinyl and vinyl tile floors with a clean ammonia scent.

• Sweep or vacuum to remove all loose dirt
• Dilute 1 part stripper to 3 parts warm water
• Liberally apply with a sponge mop and allow to soak for 5-10 minutes
• Wear gloves to avoid contact with skin. While the floor is still wet, scrub floor with a brush or nylon pad
• Mop up the dirty solution and immediately rinse floor with clean water, using a clean sponge mop
• Allow the floor to dry thoroughly
• Apply Mannington polish to restore the shine and to protect the floor

Mannington Rinse-Free Cleaner
A concentrated formula that's quick and easy to apply and has a pleasing lemon scent. Dries to a shine, leaving no dulling film. Use on all sheet vinyl and vinyl tile floors. No rinsing is required.

• Sweep or vacuum to remove all loose dirt
• Mix 1/4 cup of cleaner with a gallon of cool water.
• Using a damp sponge mop, spread this solution over 3' x 3' sections, one at a time.
• Start in the farthest corner of the room and work toward the room's entrance.
• Firmly mop the floor clean, pressing harder to loosen stubborn dirt spots.
• When the solution gets dirty, mix a fresh solution and go on to the next area.
• Allow floor to dry to a bright shine.

Metroflor™ Products

Metroflor™ Gloss & Matte Stripper - This ammoniated stripper is a concentrated stripper especially designed to remove the most sophisticated detergent-resistant waxes and acrylic finishes. It strips off the old finish and surface buildup in preparation for the application of new finishes.

Directions:

• Use 16 oz. of MF Stripper per each gallon of water.
• Apply liberally but do not flood. Excessive buildups not entirely removed may show as a white film. In such cases, scrubbing with a coarse brush or nylon pad should remove film.
• After scrubbing, pick up solution with a mop.
• Rinse the floor well with a mop slightly dampened with clear water.
• Let dry thoroughly before applying a fresh coat of finish.

Metroflor™ Gloss Finish
Metroflor Gloss Finish is a metal cross-linked floor finish which dries to a high gloss and provides a tough mar-resistant film for periodic use on laminate and vinyl floors. Helps seal against moisture and protects from dirt, scuffs and scratches.

• Preparation: Thoroughly clean floor. Remove all old finish using a stripper specially formulated for the finish and floors you are stripping. Scrub, rinse well and allow to dry.
• Application: Apply 2 light coats using a sponge mop, wax applicator and damp clean cloth
  • Place a small amount in a shallow pan and spread a thin, even coat
  • Allow to dry (tack free) for at least 30 minutes before applying a second coat
• Maintenance: Sweep, dust mop or vacuum floor daily. Maintain by damp mopping with a neutral, non-abrasive cleaner. Recoat traffic areas as needed

Metroflor™ Neutral Cleaner
Use Metroflor Neutral Cleaner for periodic maintenance of floor gloss. Maintains existing floor finish with no film. It is a no-rinse cleaner for all vinyl floors, environmentally safe - no phosphates, lemon scented and is PH neutral.

• Damp Mopping: Use 3-4 oz. per gallon of water. No rinsing is required
• Scrubbing: Use 4-6 oz. per gallon of water. Use light to medium duty pad or brush. Rinsing is required.
• Automatic scrubber: Use 2-3 oz. per gallon of water. No rinsing is required.

Metroflor™ Matte Finish
Metroflor Matte Finish gives a long lasting finish for all vinyl floors. Dries to provide a tough mar-resistant film for periodic use on all vinyl floors. Maintains a low gloss look, repels stains, and protects porous floors.

• Preparation: Thoroughly clean floor. Remove all old finish using a stripper specially formulated for the finish and floors you are stripping. Scrub, rinse well and allow to dry.
• Application: Apply the finish using a lambs wool applicator, gravity flow applicator or a rayon mop.
  • Apply 2-3 coats for optimum gloss and durability.
  • Allow to dry (tack free) for at least 30 minutes before applying a second coat
• Maintenance: Sweep, dust mop or vacuum floor daily. Maintain by damp mopping with a neutral, non-abrasive cleaner. Recoat traffic areas as needed